Skip to main content
Sunmi POS bundle

How to set up your Sunmi POS bundle

Updated over a week ago


Sunmi T2 lite

What's in the box? The Sunmi T2 lite, power adapter block, power adapter cable and user manual. Setup the device:

  • Place the T2 lite in front of you with the screen facing towards you

  • Tilt the screen backwards 90 degrees until you can see the port cover

  • Pull down the port cover to display all the ports

  • Connect the power adapter block and cable together then plug the power cable into the far right port

  • Connect the barcode scanner, printer and cash drawer (instructions below) or complete this step after the T2 lite has been activated

  • Close the port cover and tilt the screen back to its upright position

  • Ensure the power cable is plugged into the power outlet

  • Hold down the power button located on the lower left hand side of the screen


T2 lite activation and setup

Activate the T2 lite by following the activation process:

  • Tap Start setup

  • Select English as the language and tap Next

  • Select your timezone and tap Next

  • Connect the device to the internet via ethernet or tap WLAN to connect via WiFi

  • If connecting via WiFi tap your network, enter the password and tap Connect

  • Tap Start config

  • Wait for the Sunmi to configure settings and install all approved apps including Saledock POS

  • Once activated the homescreen will be shown

  • If you are using SumUp as your payment provider or a Bluetooth device ensure Bluetooth is turned on. Tap Settings on the homescreen tap Bluetooth from the list and tap the Toggle button to turn Bluetooth on

  • By default the volume is set high. On the back of the T2 lite there are 2 covers. Remove the smaller cover, from here you can adjust the volume and insert a SIM card if required

  • By default the on screen keyboard is set to English US. You will need to change this to English UK to display GBP as the default currency within the Saledock POS app. Important - If you do not change this the default currency is US Dollars.

  • From the Settings view scroll down to the Personal section and tap Languages and input then Languages

  • Tap Add a language and select English (United Kingdom) from the list

  • Tap the icon in the top right and tap Remove

  • Tap the checkbox to the left of English (United States) and tap the icon in the top right to remove the language


Sunmi 58mm receipt printer

What's in the box? The Sunmi 58mm receipt printer, power cable, USB cable, 1 paper roll and user manual. Setup the device:

  • Plug the USB-C end of the cable into the printer and the USB end into a Sunmi T2 lite USB port

  • Plug the power cable into the printer and power outlet

  • Place the printer in front of you with the power indicator facing towards you. To the left of the receipt cutter press the button to open the printer cover. Add the paper roll, bring one end of the paper roll towards the receipt cutter and close the cover ensuring the end of the roll is fed through the cutter

  • Press the switch on the bottom left of the printer to turn it on. The power indicator will light up blue to indicate power

  • The warning indicator to the right of the power indicator is lit if there is a paper jam, the paper roll is empty or the printer cover is open

  • The printer is compatible with 58mm wide rolls up to 60mm in diameter


Sunmi U2 handheld scanner

What's in the box? The Sunmi U2 handheld scanner and user manual. Plug the scanner into one of the USB port on the T2 lite. The scanner beeps and vibrates after each successful scan.


Honeywell Voyager 1202g barcode scanner

What's in the box? The Honeywell Voyager 1202g barcode scanner, interface cable, charging base. The Voyager is the wireless alternative to the Sunmi U2 barcode scanner.

Scanner setup

  • Connect the interface cable to the charging base

  • Plug the USB end of the interface cable to any USB port on the T2 lite

  • Place the scanner into the charging base

  • The scanner will beep to indicate it is connected. Charge the scanner prior to first use

  • The base displays a red LED to indicate is is turned on, the flashing green LED indicates the scanner is charging

  • The scanner displays a green LED and single beep to indicate a successful scan. A long beep and no green LED indicates the scanner is not connected to the base and the scan was unsuccessful

Troubleshooting

If the scanner is connected to Saledock and correctly setup but the barcodes are not scanning please reset the scanner to the default factory settings. Please refer to the manuals and guides list of the resources section on the Honeywell product page.


SBV standard and compact cash drawer

What's in the box? The cash drawer and 2 drawer keys. Both the standard and compact cash drawers are compatible with the Sunmi T2 lite and use a RJ11 interface. Plug the cable into the interface to the left of the power port on the T2 lite.


Next steps

Once all devices are connected and the Saledock app is installed on the device you are ready to use the Saledock POS app. Visit the POS help centre to get started. You will need to specify your active printer and scanner within the app.

Did this answer your question?